IP Digital/Parallel I/O Modules

Acromag, Inc. Tel: (248) 295-0310

Function Description

Digital Input 40 channels, 0-60V DC input, change-of-state interrupts (12 channels), TTL input threshold w/hysteresis. Model No. IP400

Digital Output 40 channels, 0-60V DC output range, high current output, failsafe power-up and system reset, -40° to 85°C option. Model No. IP405

Digital Input/Output 32 bidirectional I/O channels, 0-60V DC input, 60V DC low-side switches, loopback monitoring of outputs, -40° to 85°C option. Model No. IP408

Digital Input/Output 48 bidirectional channels, TTL-compatible inputs, CMOS-compatible open-drain outputs, interrupt support on each channel, -40° to 85°C option. Model No. IP470

Isolated Digital Input 32 Isolated input channels, interrupt support for each channel, three input ranges, -40° to 85°C option. Model No. IP440A

Digital Output 32 isolated output channels, solid-state relay outputs, ±60V AC/DC voltage range, TTL-compatible, -40° to 85°C option. Model No. IP445

Differential I/O 24 digital input and/or output channels, RS-422A/485 transceivers, interrupt support (change-of-state, hi/lo transitions), -40° to 85°C option. Model No. IP409

Counter/Timer Ten 16-bit TTL counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP482

Counter/Timer Five 16-bit TTL & two 16-bit RS422 counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP483

Counter/Timer Five 16-bit RS422 counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP484

FPGA Altera EP1K100 FPGA programmable via the IP bus, 48 TTL lines, -40° to 85°C option. Model No. IP-1K110-4800

JTAG-Reconfigurable
FPGA Module 48 TTL lines, Altera EP1K100 FPGA programmable via the JTAG port, Supports 8MHz and 32MHz IP bus, hardware support for DMA and memory space. Model No. IP-1K125-4800

FPGA-Reconfigurable
Cyclone II FPGA Digital I/O module Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 48 TTL I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP201

JTAG-Reconfigurable
Cyclone II FPGA Digital I/O Module Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 differential RS485 I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP202

JTAG-Reconfigurable
Cyclone II FPGA Digital I/O Module Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 TTL and 12 RS485 I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP203

JTAG-Reconfigurable
Cyclone II FPGA Digital I/O Module Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 LVDS I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP204

Function	Description
Digital Input	40 channels, 0-60V DC input, change-of-state interrupts (12 channels), TTL input threshold w/hysteresis. Model No. IP400
Digital Output	40 channels, 0-60V DC output range, high current output, failsafe power-up and system reset, -40° to 85°C option. Model No. IP405
Digital Input/Output	32 bidirectional I/O channels, 0-60V DC input, 60V DC low-side switches, loopback monitoring of outputs, -40° to 85°C option. Model No. IP408
Digital Input/Output	48 bidirectional channels, TTL-compatible inputs, CMOS-compatible open-drain outputs, interrupt support on each channel, -40° to 85°C option. Model No. IP470
Isolated Digital Input	32 Isolated input channels, interrupt support for each channel, three input ranges, -40° to 85°C option. Model No. IP440A
Digital Output	32 isolated output channels, solid-state relay outputs, ±60V AC/DC voltage range, TTL-compatible, -40° to 85°C option. Model No. IP445
Differential I/O	24 digital input and/or output channels, RS-422A/485 transceivers, interrupt support (change-of-state, hi/lo transitions), -40° to 85°C option. Model No. IP409
Counter/Timer	Ten 16-bit TTL counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP482
Counter/Timer	Five 16-bit TTL & two 16-bit RS422 counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP483
Counter/Timer	Five 16-bit RS422 counter/timers, waveform generation, frequency/period/pulse-width measurement, quadrature, interrupts, 32-bit counter/timer, -40° to 85°C option. Model No. IP484
FPGA	Altera EP1K100 FPGA programmable via the IP bus, 48 TTL lines, -40° to 85°C option. Model No. IP-1K110-4800
JTAG-Reconfigurable FPGA Module	48 TTL lines, Altera EP1K100 FPGA programmable via the JTAG port, Supports 8MHz and 32MHz IP bus, hardware support for DMA and memory space. Model No. IP-1K125-4800
FPGA-Reconfigurable Cyclone II FPGA Digital I/O module	Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 48 TTL I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP201
JTAG-Reconfigurable Cyclone II FPGA Digital I/O Module	Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 differential RS485 I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP202
JTAG-Reconfigurable Cyclone II FPGA Digital I/O Module	Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 TTL and 12 RS485 I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP203
JTAG-Reconfigurable Cyclone II FPGA Digital I/O Module	Altera Cyclone II FPGA programmable via the JTAG port or IP bus, 24 LVDS I/O lines, supports 8MHz and 32MHz IP bus. -40° to 85° option. Model No. IP-EP204

Alphi Technology Tel: (480) 838-2428

Function Description

TTL I/O 32 digital TTL level input / outputs, counters times, 2 x 8536 CIO single wide Industry Pack. Model No. ATC-CIO32

OPTO 16 digital Opto-isolated inputs, counters/timers, 8536 CIO single wide Industry Pack. Model No. ATC-OPTOin

OPTO 16 digital Opto-isolated Outputs, counters/timers, 8536 CIO single wide Industry Pack. Model No. ATC-OPTOout

FPGA Xilinx 4020, 42 user TTL I/O, 1 meg SRAM, single wide Industry Pack. Model No. ATC-FPGA

FPGA ALTERA 10kxx Series, 42 user ttl I/O, .5 meg SRAM, single wide Industry Pack. Model No. ATC-ALTERA-xx

Function	Description
TTL I/O	32 digital TTL level input / outputs, counters times, 2 x 8536 CIO single wide Industry Pack. Model No. ATC-CIO32
OPTO	16 digital Opto-isolated inputs, counters/timers, 8536 CIO single wide Industry Pack. Model No. ATC-OPTOin
OPTO	16 digital Opto-isolated Outputs, counters/timers, 8536 CIO single wide Industry Pack. Model No. ATC-OPTOout
FPGA	Xilinx 4020, 42 user TTL I/O, 1 meg SRAM, single wide Industry Pack. Model No. ATC-FPGA
FPGA	ALTERA 10kxx Series, 42 user ttl I/O, .5 meg SRAM, single wide Industry Pack. Model No. ATC-ALTERA-xx

Dynatem Tel: (949) 855-3235

Function Description

16 Digital
Inputs 24V DC, 0.5A; opt. extended temperature. Model No. IPM03

16 Digital
Outputs 24V DC, 0.5A; opt. extended temperature. Model No. IPM04

Function	Description
16 Digital Inputs	24V DC, 0.5A; opt. extended temperature. Model No. IPM03
16 Digital Outputs	24V DC, 0.5A; opt. extended temperature. Model No. IPM04

Hytec Electronics Tel: +44 (0) 118 9757770

Function Description

Digital I/O 16-channel I/O Industry pack. 16 inputs or 16 outputs or 8in and 8 out. Model No. IP-DIGIO-8505

Isolated
Digital Input
Transition Board 6U VME64x base card. Accepts four sets of 16 optically isolated inputs and control signals. Four 50 way SCSI-2. Model No. VTB8301

Isolated
Digital
Input/Output
Transition Board 6U VME64x base card. Accepts two sets and outputs two sets of 16 optically isolated data and control signals. Four 50-way SCSI-2. Model No. VTB8302

Isolated
Digital Output
Transition Board 6U VME64x base card. Used with the 8001. In Out, four sets of 16 data and two optically isolated control bits. Model No. VTB8303

Straight-Through
Transition Board 6U VME64x base card. Connects the IP cards I/O signals directly to the four 50 way SCSI-2 connectors. No provision for DC/DC converters. Model No. VTB8304

Isolated
Digital
Input/Output
Transition Board 6U VME64x base card. Two sets of optically isolated 16 bit + two control line inputs and two sets of outputs. Model No. VTB8305

Function	Description
Digital I/O	16-channel I/O Industry pack. 16 inputs or 16 outputs or 8in and 8 out. Model No. IP-DIGIO-8505
Isolated Digital Input Transition Board	6U VME64x base card. Accepts four sets of 16 optically isolated inputs and control signals. Four 50 way SCSI-2. Model No. VTB8301
Isolated Digital Input/Output Transition Board	6U VME64x base card. Accepts two sets and outputs two sets of 16 optically isolated data and control signals. Four 50-way SCSI-2. Model No. VTB8302
Isolated Digital Output Transition Board	6U VME64x base card. Used with the 8001. In Out, four sets of 16 data and two optically isolated control bits. Model No. VTB8303
Straight-Through Transition Board	6U VME64x base card. Connects the IP cards I/O signals directly to the four 50 way SCSI-2 connectors. No provision for DC/DC converters. Model No. VTB8304
Isolated Digital Input/Output Transition Board	6U VME64x base card. Two sets of optically isolated 16 bit + two control line inputs and two sets of outputs. Model No. VTB8305

SBS Technologies Tel: (505)-875-0600

Function Description

16 Digital
Inputs 16 interrupt generating digital inputs. 24V signal voltage for inputs. -40 to +85 C. Model No. IP-OPTOINPUT16

16 Digital
Inputs 16 interrupt generating optically isolated digital inputs. Commercial temperature range. Model No. IP-OPTOINPUT16C

8 Digital
Input/Output 8 digital optically isolated inputs and 8 optically isolated outputs; 24V signal voltage. Model No. IP-OPTOIO-8

16 Digital
Outputs 16 optically isolated digital outputs, high and low side switches. 24V signal voltage. Model No. IP-OPTOOUT-16

24 TTL
Lines 24 buffered TTL digital I/O lines with high current output drivers and wide voltage range inputs. 64 mA +15/-5V operation. Each line may be configured for either input or output. Inputs and outputs may be double-buffered, making it compatible with simulation systems requiring many inputs and outputs to be latched simultaneously. Model No. IP-UD

Differential
Digital I/O 24 differential digital I/O lines. Common mode range -7V to +12V with 70 mV hysteresis. Uses EIA-422 drivers and receivers; includes terminators. Model No. IP-UD-D

24 TTL-Level
Digital I/O 24 flexible TTL-level I/O lines and ESD protection. Each line may be configured for either input or output. Inputs and outputs may be double buffered. Model No. IP-UD-E

48 TTL-Level
Digital I/O 48 TTL-level digital I/O lines. All lines have LineSafe ESD protection. Double-buffered input and output. Model No. IP-UD-E-48

24 TTL-Level
Digital I/O 24 buffered TTL digital I/O lines that can generate interrupts. All lines individually programmed to generate interrupts. All lines individually programmed to generate interrupts. Model No. IP-UD-I

24 Flexible
Input/Output 24 flexible input/output lines with differential output drivers and differential inputs. Any input may be programmed to generate an interrupt. Inputs and output meet EIA-422 and EIA-485 specifications with an extended common mode range of +12V to -7V. Model No. IP-UD-ID

24 Flexible
TTL I/O 24 flexible TTL-level input/output lines. Each line may be dynamically and individually configured for either input or output providing maximum flexibility. All lines have LineSafe ESD protection. All inputs may generate interrupts. Model No. IP-UD-IE

TTL Level
Digital I/O 48 TTL level tristate digital I/O lines with pullups, interrupts, debounce and ESD. I/O lines individually programmable. -40 to +85C. Model No. IP-DIO48-ET

28 Lines
Digital I/O 20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. Champ cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-CM50

28 Lines
Digital I/O 20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. High-density cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-HD50

28 Lines
Digital I/O 20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. Flat ribbon cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-IP50

TTL I/O TTL lines have LineSafe ESD protection circuit. TTL I/O. ARINC 429 interface. 4 RX and 2 TX channels. ARINC 429 interface. 8 RX and 4 TX channels. Model No. IP-ALTERA-TTL

16
Digital
Inputs 16 interrupt generating optically isolated digital inputs. 44V signal voltage for all 16 inputs. For avionics test environments. -40 to +85 C. Model No. IP-OPTOAV16-ET

24 High
Voltage Lines 24 high-voltage I/O lines. 16 inputs and 8 outputs. Programmable input voltage threshold to 100V, Output to 50V and 1A. Both inputs and outputs are double buffered. Model No. IP-UD-HV-16I80

High Voltage 16 inputs, 8 outputs, and interrupts. Each input line capable of generating an interrupt. Interrupt latch circuits are edge sensitive with programmable polarity and are controlled through five registers. Each line corresponds to 1 bit in each of the registers, making programming uniform and simple. Model No. IP-UD-IHV-16I80

16
High Side
Switches 16 opto-isolated high side switches with 48V, 1A capacity, watchdog timer, and short circuit protection. Output signal voltage 6V to 48V. -40 to +85C. Model No. IP-DRV16-ET

Relays 8 form C (double pole, double throw) latching relays. Model No. IP-RELAY

Pulse Width
Input 3 Pulse Width Input channels. Model No. IP-PWI

High Voltage 16 inputs and 8 outputs. All inputs can be programmed to generate an interrupt. Model No. IP-UD-IHV-16I80

Function	Description
16 Digital Inputs	16 interrupt generating digital inputs. 24V signal voltage for inputs. -40 to +85 C. Model No. IP-OPTOINPUT16
16 Digital Inputs	16 interrupt generating optically isolated digital inputs. Commercial temperature range. Model No. IP-OPTOINPUT16C
8 Digital Input/Output	8 digital optically isolated inputs and 8 optically isolated outputs; 24V signal voltage. Model No. IP-OPTOIO-8
16 Digital Outputs	16 optically isolated digital outputs, high and low side switches. 24V signal voltage. Model No. IP-OPTOOUT-16
24 TTL Lines	24 buffered TTL digital I/O lines with high current output drivers and wide voltage range inputs. 64 mA +15/-5V operation. Each line may be configured for either input or output. Inputs and outputs may be double-buffered, making it compatible with simulation systems requiring many inputs and outputs to be latched simultaneously. Model No. IP-UD
Differential Digital I/O	24 differential digital I/O lines. Common mode range -7V to +12V with 70 mV hysteresis. Uses EIA-422 drivers and receivers; includes terminators. Model No. IP-UD-D
24 TTL-Level Digital I/O	24 flexible TTL-level I/O lines and ESD protection. Each line may be configured for either input or output. Inputs and outputs may be double buffered. Model No. IP-UD-E
48 TTL-Level Digital I/O	48 TTL-level digital I/O lines. All lines have LineSafe ESD protection. Double-buffered input and output. Model No. IP-UD-E-48
24 TTL-Level Digital I/O	24 buffered TTL digital I/O lines that can generate interrupts. All lines individually programmed to generate interrupts. All lines individually programmed to generate interrupts. Model No. IP-UD-I
24 Flexible Input/Output	24 flexible input/output lines with differential output drivers and differential inputs. Any input may be programmed to generate an interrupt. Inputs and output meet EIA-422 and EIA-485 specifications with an extended common mode range of +12V to -7V. Model No. IP-UD-ID
24 Flexible TTL I/O	24 flexible TTL-level input/output lines. Each line may be dynamically and individually configured for either input or output providing maximum flexibility. All lines have LineSafe ESD protection. All inputs may generate interrupts. Model No. IP-UD-IE
TTL Level Digital I/O	48 TTL level tristate digital I/O lines with pullups, interrupts, debounce and ESD. I/O lines individually programmable. -40 to +85C. Model No. IP-DIO48-ET
28 Lines Digital I/O	20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. Champ cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-CM50
28 Lines Digital I/O	20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. High-density cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-HD50
28 Lines Digital I/O	20 differential I/O lines and 8 digital TTL I/O lines. Direction of each I/O line is programmable. TTL lines have LineSafe ESD protection circuit. Flat ribbon cable and IP-TERM-HD50. Altera design file-set. Model No. IP-ALTERA-IP50
TTL I/O	TTL lines have LineSafe ESD protection circuit. TTL I/O. ARINC 429 interface. 4 RX and 2 TX channels. ARINC 429 interface. 8 RX and 4 TX channels. Model No. IP-ALTERA-TTL
16 Digital Inputs	16 interrupt generating optically isolated digital inputs. 44V signal voltage for all 16 inputs. For avionics test environments. -40 to +85 C. Model No. IP-OPTOAV16-ET
24 High Voltage Lines	24 high-voltage I/O lines. 16 inputs and 8 outputs. Programmable input voltage threshold to 100V, Output to 50V and 1A. Both inputs and outputs are double buffered. Model No. IP-UD-HV-16I80
High Voltage	16 inputs, 8 outputs, and interrupts. Each input line capable of generating an interrupt. Interrupt latch circuits are edge sensitive with programmable polarity and are controlled through five registers. Each line corresponds to 1 bit in each of the registers, making programming uniform and simple. Model No. IP-UD-IHV-16I80
16 High Side Switches	16 opto-isolated high side switches with 48V, 1A capacity, watchdog timer, and short circuit protection. Output signal voltage 6V to 48V. -40 to +85C. Model No. IP-DRV16-ET
Relays	8 form C (double pole, double throw) latching relays. Model No. IP-RELAY
Pulse Width Input	3 Pulse Width Input channels. Model No. IP-PWI
High Voltage	16 inputs and 8 outputs. All inputs can be programmed to generate an interrupt. Model No. IP-UD-IHV-16I80

TEWS Technologies Tel: +49 4101 4058-0, (775) 686 6077

Function Description

16 Digital Input
24V DC Optically isolated, fully programmable interrupt capabilities, electronic debounce (TIP600-10) (TIP605-10-ext. temp range)

16 Digital
Inputs for
Avionic
Applications 16 digital inputs designed for avionic applications, Input voltage typ. 28V, max 42V, optically isolated; Differential high impedance input (typ. 118 kW); Input threshold for high level typ. >14V; input threshold for low level typ. <3,5V; fully programmable interrupt capabilities; electron. debounce; -40°C to +85°C (TIP606-10)

TTL I/O 20 digital TTL I/O's based on Zilog Z8536 controller arranged as two 8-bit I/O ports and a 4-bit control port; 0°C to +70°C (TIP610-10)

48 Line
Digital
Interface Up to 48 digital TTL I/O lines; Emulates two Motorola MC68230 Programmable Interface/Timer; TTL compatible: 3.3V output high level, 5V tolerant; Termination: 10kohms pull-ups to 3.3V; Output current max. ±2mA (partly ±8mA); ESD and overvoltage protection for each I/O line; -40°C to +85°C (TIP620-10). Configured to support additional features of the PI/Ts (TIP620-11)

4 or 8 Digital
Input/Output
24V DC 8 digital input 24V DC, 8 digital output 24V DC 0.5A, optically isolated, fully programmable interrupt capabilities, electronic debounce, overload and short cicuit protection, Ext. Temp range. 8 output (TIP670-10), 4 output TIP670-20)

24 Digital I/O
(w/Interrupts) 24 digital I/O lines with differential EIA-422 / EIA-485 compatible ESD protected line driver / receiver (individually programmable as input or output); Full interrupt capability on inputs; Six 4 x 120ohms resistor networks mounted in sockets for I/O line termination; Programmable simultaneous update feature by external clock source (TTL level); 0°C to +70°C (TIP672-10)

48 TTL
I/O Lines
w/Interrupts 48 digital TTL tri-state I/O lines with pull up resistors; I/O lines individually programmable as input or output; Full interrupt capability on inputs; Electronic debounce circuit for interrupt; ESD and overvoltage protection; Resistor networks mounted in sockets as I/O line pull up; Programmable simultaneous update feature by external clock source (TTL level); -40°C to +85°C (TIP675-10)

8 or 16
Digital Output
24V DC 0.5A, optically isolated, channels are isolated against each other in sets of two, overload and short circuit protection, Ext. Temp range. 16 outputs (TIP700-10), 8 outputs (TIP700-20)

16 Digital Output
High Side Switch 16 digital outputs, high side switch; Output signal voltage 6V to 48V, common to all outputs, externally supplied; Output current: 1A continuous per channel; Optocouplers for galvanic isolation of outputs to computer system, Overload and short circuit protection; Watchdog timer resets all channels in case of triggering failure; -40°C to +85°C (TIP710-10)

Function	Description
16 Digital Input 24V DC	Optically isolated, fully programmable interrupt capabilities, electronic debounce (TIP600-10) (TIP605-10-ext. temp range)
16 Digital Inputs for Avionic Applications	16 digital inputs designed for avionic applications, Input voltage typ. 28V, max 42V, optically isolated; Differential high impedance input (typ. 118 kW); Input threshold for high level typ. >14V; input threshold for low level typ. <3,5V; fully programmable interrupt capabilities; electron. debounce; -40°C to +85°C (TIP606-10)
TTL I/O	20 digital TTL I/O's based on Zilog Z8536 controller arranged as two 8-bit I/O ports and a 4-bit control port; 0°C to +70°C (TIP610-10)
48 Line Digital Interface	Up to 48 digital TTL I/O lines; Emulates two Motorola MC68230 Programmable Interface/Timer; TTL compatible: 3.3V output high level, 5V tolerant; Termination: 10kohms pull-ups to 3.3V; Output current max. ±2mA (partly ±8mA); ESD and overvoltage protection for each I/O line; -40°C to +85°C (TIP620-10). Configured to support additional features of the PI/Ts (TIP620-11)
4 or 8 Digital Input/Output 24V DC	8 digital input 24V DC, 8 digital output 24V DC 0.5A, optically isolated, fully programmable interrupt capabilities, electronic debounce, overload and short cicuit protection, Ext. Temp range. 8 output (TIP670-10), 4 output TIP670-20)
24 Digital I/O (w/Interrupts)	24 digital I/O lines with differential EIA-422 / EIA-485 compatible ESD protected line driver / receiver (individually programmable as input or output); Full interrupt capability on inputs; Six 4 x 120ohms resistor networks mounted in sockets for I/O line termination; Programmable simultaneous update feature by external clock source (TTL level); 0°C to +70°C (TIP672-10)
48 TTL I/O Lines w/Interrupts	48 digital TTL tri-state I/O lines with pull up resistors; I/O lines individually programmable as input or output; Full interrupt capability on inputs; Electronic debounce circuit for interrupt; ESD and overvoltage protection; Resistor networks mounted in sockets as I/O line pull up; Programmable simultaneous update feature by external clock source (TTL level); -40°C to +85°C (TIP675-10)
8 or 16 Digital Output 24V DC	0.5A, optically isolated, channels are isolated against each other in sets of two, overload and short circuit protection, Ext. Temp range. 16 outputs (TIP700-10), 8 outputs (TIP700-20)
16 Digital Output High Side Switch	16 digital outputs, high side switch; Output signal voltage 6V to 48V, common to all outputs, externally supplied; Output current: 1A continuous per channel; Optocouplers for galvanic isolation of outputs to computer system, Overload and short circuit protection; Watchdog timer resets all channels in case of triggering failure; -40°C to +85°C (TIP710-10)

Return To IP Module Index / Return To Mezzanine Directory Index / Return To VME Directory Main Page